Orvis reel handle “donut”nut
Orvis reel handle “donut”nut
I am looking for the nut for the handle of an Orvis third model. As appears below, it has an opening which I assume was to facilitate oiling. If anyone knows a good website for antique brass nuts and bolts hardware, it would be appreciated.
PS This is photo of an Orvis handle from Ron G.’s website, where every reel google or other search engine ultimately sends you.
PS This is photo of an Orvis handle from Ron G.’s website, where every reel google or other search engine ultimately sends you.
Last edited by Mike N on Tue Oct 24, 2017 7:10 pm, edited 1 time in total.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- Jim Schottenham
- Super Board Poster
- Posts: 827
- Joined: Sat Sep 13, 2003 10:27 pm
- Location: Upstate NY
- Contact:
Re: Orvis reel handle “donut”nut
Mike,
I don't see anything missing. That handle should just screw off, counter clockwise.
I don't see anything missing. That handle should just screw off, counter clockwise.
- Midway Tommy D
- Star Board Poster
- Posts: 3142
- Joined: Sun Jan 20, 2013 11:23 pm
- Location: Eastern NE
Re: Orvis reel handle “donut”nut
Jim,
I think Mike just posted an example of what he is looking for, not the reel that needs one.
I think Mike just posted an example of what he is looking for, not the reel that needs one.
Love those Open Face Spinning Reels! (Especially ABU & ABU/Zebco)
Tom DeLong, NE
ORCA Member - 2027
Tom DeLong, NE
ORCA Member - 2027
Re: Orvis reel handle “donut”nut
Thanks, Jim and Tommy.
Tommy is correct that I posted a photo above as what I am looking for. I assume Jim is saying the “nut” is actually attached as part of the handle.
Below are my two Orvis reels. I believe the one (third model) on the left has an incorrect handle or nut, or both. I think the first model below right is correct? Thoughts?
Tommy is correct that I posted a photo above as what I am looking for. I assume Jim is saying the “nut” is actually attached as part of the handle.
Below are my two Orvis reels. I believe the one (third model) on the left has an incorrect handle or nut, or both. I think the first model below right is correct? Thoughts?
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- RonG
- Super Board Poster
- Posts: 1474
- Joined: Fri Oct 24, 2003 8:49 pm
- Location: Frostproof, FL
- Contact:
Re: Orvis reel handle “donut”nut
Your reel looks complete as Jim says. Here's a photo of another one. Wait a minute, that is a photo of my reel.
Ron Gast
https://reelsnlures.com
https://reelsnlures.com
Re: Orvis reel handle “donut”nut
When you write the authoritative reel encyclopedia, you have to expect to be quoted.
What are your thoughts on the reel on the left, Ron?
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- RonG
- Super Board Poster
- Posts: 1474
- Joined: Fri Oct 24, 2003 8:49 pm
- Location: Frostproof, FL
- Contact:
Re: Orvis reel handle “donut”nut
Take the nut off and let's see what it looks like.
Ron Gast
https://reelsnlures.com
https://reelsnlures.com
- Jim Schottenham
- Super Board Poster
- Posts: 827
- Joined: Sat Sep 13, 2003 10:27 pm
- Location: Upstate NY
- Contact:
Re: Orvis reel handle “donut”nut
Mike,
No doubt in my mind that the nut on the left reel is not original. The handle itself looks OK, but I agree with Ron - we need to see the spindle under that nut.
No doubt in my mind that the nut on the left reel is not original. The handle itself looks OK, but I agree with Ron - we need to see the spindle under that nut.
Re: Orvis reel handle “donut”nut
Last edited by Mike N on Tue Oct 24, 2017 8:04 pm, edited 1 time in total.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
Re: Orvis reel handle “donut”nut
Jim- What do you think of the handle after viewing the photos above of the Orvis THIRD model? Do you agree that it needs a similar donut-style nut? The nut is an old replacement off another reel. That is why I inquired about a “donut” nut.Jim Schottenham wrote:Mike,
No doubt in my mind that the nut on the left reel is not original. The handle itself looks OK, but I agree with Ron - we need to see the spindle under that nut.
I cannot find additional Third Model photos.
Here are a few photos from other sources of handles on an Orvis FIRST model:
This 1874 patent First model is from Silvio Calabi’s book, page 80:
This 1874 patent First model is from Jim Brown’s A Treasury of Reels, page 97.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- RonG
- Super Board Poster
- Posts: 1474
- Joined: Fri Oct 24, 2003 8:49 pm
- Location: Frostproof, FL
- Contact:
Re: Orvis reel handle “donut”nut
Is it possible the threads in the handle were drilled out? In this case you would need a nut to pull the handle down against the spool shaft. Is there a shoulder on the spool shaft that the handle would bear against? Without a threaded shaft and handle that would bottom out when tightened, typically you have a square feature on the spool shaft and handle for torque application.
Ron Gast
https://reelsnlures.com
https://reelsnlures.com
Re: Orvis reel handle “donut”nut
Ron- The shaft is threaded and the handle screws right on and off perfectly. The correct nut is missing.
I assume the threaded shaft is hollow for oiling the reel.
If anyone else has a third model, I would appreciate a few photos. After a few decades collecting only Kentucky reels, I’m in a new learning curve with these old fly reels. Thanks.
I assume the threaded shaft is hollow for oiling the reel.
If anyone else has a third model, I would appreciate a few photos. After a few decades collecting only Kentucky reels, I’m in a new learning curve with these old fly reels. Thanks.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- RonG
- Super Board Poster
- Posts: 1474
- Joined: Fri Oct 24, 2003 8:49 pm
- Location: Frostproof, FL
- Contact:
Re: Orvis reel handle “donut”nut
Sounds like you just screw the handle down tight and that's it. This is typical of a lot of fly and salmon reels, especially Julius vom Hofe reels.
Ron Gast
https://reelsnlures.com
https://reelsnlures.com
Re: Orvis reel handle “donut”nut
That’s an interesting observation and probably correct, Ron, especially when you consider the Orvis first model where the handle had to be frequently removed to store it in the wooden box.RonG wrote:Sounds like you just screw the handle down tight and that's it. This is typical of a lot of fly and salmon reels, especially Julius vom Hofe reels.
But as you can see from the photos above of the third model, screwing the handle down doesn’t leave the handle flush with the end of the threaded shaft, but instead there is about an 1/8” gap as if for a retaining nut.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- reelsmith.
- Ultra Board Poster
- Posts: 1715
- Joined: Sun Sep 14, 2003 11:08 am
- Location: Connecticut
- Contact:
Re: Orvis reel handle “donut”nut
Hey Mike.
It looks like the half-handle on your other Orvis is much thicker.
Have you tried putting it on the other reel to see if it covers all the threads ?
Dean.
It looks like the half-handle on your other Orvis is much thicker.
Have you tried putting it on the other reel to see if it covers all the threads ?
Dean.
Wanted: Kosmic Items, Small Leather Fly Reel Cases, Early Fishing Related Bottles, Fly Reels and Pre-1900 Angling/Casting Medals.
http://www.tackletreasures.com/
http://www.tackletreasures.com/
Re: Orvis reel handle “donut”nut
Very good observation, Dean. I will try that when I get home. However, it still does not explain the need for the "donut" type of nut or washer that appears in the very first photos in this thread on Ron G.'s reel. Curious.reelsmith. wrote:Hey Mike.
It looks like the half-handle on your other Orvis is much thicker.
Have you tried putting it on the other reel to see if it covers all the threads ?
Dean.
Thanks
Mike N.
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990
- RonG
- Super Board Poster
- Posts: 1474
- Joined: Fri Oct 24, 2003 8:49 pm
- Location: Frostproof, FL
- Contact:
Re: Orvis reel handle “donut”nut
I think I finally see what Mike is talking about. There is a difference between the two. Sorry, I no longer have the reel and can't investigate further.
Ron Gast
https://reelsnlures.com
https://reelsnlures.com
- reelsmith.
- Ultra Board Poster
- Posts: 1715
- Joined: Sun Sep 14, 2003 11:08 am
- Location: Connecticut
- Contact:
Re: Orvis reel handle “donut”nut
I think in these two pictures we are looking at the same thing, just one handle covers the threads and the other does not.
Maybe the spool end on Mike's reel is longer ?
Dean.
Maybe the spool end on Mike's reel is longer ?
Dean.
Wanted: Kosmic Items, Small Leather Fly Reel Cases, Early Fishing Related Bottles, Fly Reels and Pre-1900 Angling/Casting Medals.
http://www.tackletreasures.com/
http://www.tackletreasures.com/
- Jim Schottenham
- Super Board Poster
- Posts: 827
- Joined: Sat Sep 13, 2003 10:27 pm
- Location: Upstate NY
- Contact:
Re: Orvis reel handle “donut”nut
Mike,However, it still does not explain the need for the "donut" type of nut or washer that appears in the very first photos in this thread on Ron G.'s reel
I don't believe that Ron's reel had a nut at the end of the threaded spindle. None of the Orvis reels I've handled or have seen ever had one, all just having the threaded handle that screws on and off. The purpose of the hollow spindle is explained in the patent - Orvis intended it to aid in drying the line, allowing the water an additional place to escape. Early reels had a "perforated" hub, later models such as yours had a single hole to allow line to pass through, knot and secure line for winding.
If you PM me your address I'll send you a copy of Jim Brown's great article on these reels. I think you'd enjoy it.
Jim
Re: Orvis reel handle “donut”nut
Who’d-a-thunk that hole was for air to dry the line? You are still numero uno, Jim, when it comes to vetting a reel.Jim Schottenham wrote:Mike,However, it still does not explain the need for the "donut" type of nut or washer that appears in the very first photos in this thread on Ron G.'s reel
I don't believe that Ron's reel had a nut at the end of the threaded spindle. None of the Orvis reels I've handled or have seen ever had one, all just having the threaded handle that screws on and off. The purpose of the hollow spindle is explained in the patent - Orvis intended it to aid in drying the line, allowing the water an additional place to escape. Early reels had a "perforated" hub, later models such as yours had a single hole to allow line to pass through, knot and secure line for winding.
If you PM me your address I'll send you a copy of Jim Brown's great article on these reels. I think you'd enjoy it.
Jim
Thanks
Mike N
Mike N.
ORCA Founder, 1990
ORCA Founder, 1990