Penn 140 Squidder Repair
- Wayne B.
- Super Board Poster
- Posts: 1024
- Joined: Sat Aug 15, 2009 7:46 am
- Location: Virginia Beach
- Contact:
Penn 140 Squidder Repair
A friend asked me to clean and lube his old Squidder. Best we can tell, it is a late 40's reel. Everything was going well until I tried to remove the headplate. It is stuck and I don't know how to free it up. I have tried light oil, I have tried an hour so in an ultrasonic bath of vinegar and water, and I have sprayed penetrating oil around the seam. One question that I can't remember...which way does the black headplate relative to the plated ring. If I am trying to free it, which way should I be twisting it?
Any help is appreciated!
Any help is appreciated!
Last edited by Wayne B. on Wed Mar 09, 2011 6:51 am, edited 1 time in total.
- john elder
- Star Board Poster
- Posts: 8555
- Joined: Mon Sep 22, 2003 2:44 pm
It's lefty-loosey (counterclockwise)...righty-tighty (clockwise) I assume you've loosened the spring-loaded pin that holds it tight and you are holding out on it while you turn? Unless it's been jammed sidewise, it should screw off with about a quarter turn. If it still won't come, then what you're doing is about the safest thing you can do...sneak penetrating oil in the crack between the sideplate and the rim and be patient. I usually put the reel in a good quality zip-loc bag with a bit of penetrating oil so you can submerge the trouble area. If that doesn't do in a couple days of treatment, you might try a heat gun on the metal to encourage it, but I think it will not be needed.
one other thing...it's sometimes hard to get a good grip and hold that pin out at the same time. I hold the back plate side in the palm of my left hand...grasp the handle/drag wheel with the last three fingers and palm of the right hand and hold out on the screw with the thumb and forefinger and twist away.
one other thing...it's sometimes hard to get a good grip and hold that pin out at the same time. I hold the back plate side in the palm of my left hand...grasp the handle/drag wheel with the last three fingers and palm of the right hand and hold out on the screw with the thumb and forefinger and twist away.
- m3040c
- Ultra Board Poster
- Posts: 2485
- Joined: Sat Apr 29, 2006 10:52 pm
- Location: Long Island, New York
I have had this problem about a hundred times. My solution was to have two simple items which work all the time with no damage to the reel. First is to mount a reel seat onto a dowel so you can clamp the dowel into a vice. This will enable you to solidly mount the reel onto the reel seat and have the vice hold it solid. The next thing you need is a small strap wrench. If you have ever been in a pubic bathroom and seen a flushometer on the toilet bowl or urinal you will notice it has a round top cap. Any plumbing supply can sell you the small plastic strap wrench that is designed to remove that cap. One brand that makes it is Sloan. That small strap wrench is the perfect tool for removing stuck side plates. The body of the wrench is plastic and the strap is a strong enough rubber belt material to remove the plate without damaging the side plate. The investment will be under $5.00 and with it you can now unscrew many side plates that are under 5 inches.
The Lefty-Loosey rule presented by Mr. Elder is the perfect direction. Counter clockwise is the direction for the spring loaded plate retaining screw and the direction the head plate needs to be turned.
BTW, a 155 is a Beachmaster. The Squidder's from that era would be a 145 or a 140.
Good Luck
The Lefty-Loosey rule presented by Mr. Elder is the perfect direction. Counter clockwise is the direction for the spring loaded plate retaining screw and the direction the head plate needs to be turned.
BTW, a 155 is a Beachmaster. The Squidder's from that era would be a 145 or a 140.
Good Luck
- john elder
- Star Board Poster
- Posts: 8555
- Joined: Mon Sep 22, 2003 2:44 pm
- Wayne B.
- Super Board Poster
- Posts: 1024
- Joined: Sat Aug 15, 2009 7:46 am
- Location: Virginia Beach
- Contact:
John:
If it had been my own reel, we would still be on the mat!
Since it is a friend's reel, I limited my efforts. I did rig a way to have it in a vise and tried the strap wrench approach. No success.
Trust me, I could get that thing loose, but it would look ugly when I was done. A 4" pipe wrench can doing almost anything!
Sorry, I failed! Again, if it was mine, I would still be more aggressive.
Wayne
If it had been my own reel, we would still be on the mat!
Since it is a friend's reel, I limited my efforts. I did rig a way to have it in a vise and tried the strap wrench approach. No success.
Trust me, I could get that thing loose, but it would look ugly when I was done. A 4" pipe wrench can doing almost anything!
Sorry, I failed! Again, if it was mine, I would still be more aggressive.
Wayne
- john elder
- Star Board Poster
- Posts: 8555
- Joined: Mon Sep 22, 2003 2:44 pm