Good replacement ones can't be found in many cases,this one is for an old j.c.higgins.
This one had .018 out of round in the level wind hole. the l.w. screw was still in good condition, .200 dia.is a standard size on many of those.
the guide is held in a precision vise on a mini mill, hole indicated in, and plunge cut with a 7/32 end mill,this trues up the hole and a thin wall bushing is turned in the lathe and pressed in.
back in the mill the pawl hole is indicated in, bushing is center drilled, drilled to 11/64 and reamed with a 3/16 reamer which is pawl hole dia.
the reel also had a broken off foot pillar,that was repaired by drilling and pressing in a new end and drilling and tapping for the 2-56 plate screw.
Worn out line guides in old baitcasters
-
- Advanced Board Poster
- Posts: 117
- Joined: Sun Sep 17, 2006 1:16 pm
- Location: mpls
-
- Advanced Board Poster
- Posts: 297
- Joined: Sat Aug 30, 2014 10:01 am
- Location: in a van down by the River
- Contact:
Re: Worn out line guides in old baitcasters
Very Nice Work Indeed .
A Government Machine Shop could most likely Replicate your work to +or - 2.4 MM for just under 2.5 Million Dollars in under 6 months.
A Government Machine Shop could most likely Replicate your work to +or - 2.4 MM for just under 2.5 Million Dollars in under 6 months.
- Paul M
- Ultra Board Poster
- Posts: 2200
- Joined: Fri Feb 03, 2006 9:10 pm
- Location: Toronto, Canada
- Contact:
Re: Worn out line guides in old baitcasters
Skills of a master! Thanks for sharing.
Paul Manuel
Member since 2006
Member since 2006
-
- Advanced Board Poster
- Posts: 117
- Joined: Sun Sep 17, 2006 1:16 pm
- Location: mpls
Re: Worn out line guides in old baitcasters
Thanks for the nice comments,if i do sell items that have machining or alterations that would be disclosed.
gene
gene
- Rick H
- Ultra Board Poster
- Posts: 1562
- Joined: Wed Oct 29, 2008 9:23 pm
- Location: Hilliard, Fl.
- Contact:
Re: Worn out line guides in old baitcasters
Gene, I've seen a lot of restoration work done over time. There's a lot of guys that'll put a lot of time, money and machinery into making / re-making damaged, missing or broken parts. Most of those kinds of efforts "always" seem to be on the higher end reels...that need saving(?). You Sir, take restoration to a new level. The reel that you restored, would normally (IMHO) not even get a blink or a nod from the average collector, even in mint condition in the box.
It's VERY NICE to see someone who will put that kind of time and effort (not to mention machinery costs), into an old reel, that would not normally be considered (by most) a "collectible". Not to say people don't collect them. Some do. It's beyond refreshing to see someone like you that "just saves" a reel....any reel. They all have stories and they all are worth saving. Nicely Done !!!!
It's VERY NICE to see someone who will put that kind of time and effort (not to mention machinery costs), into an old reel, that would not normally be considered (by most) a "collectible". Not to say people don't collect them. Some do. It's beyond refreshing to see someone like you that "just saves" a reel....any reel. They all have stories and they all are worth saving. Nicely Done !!!!
Rick Heitman
- Bad Casts, backlash, no bites? Check the Nut holding the rod !! -
- Bad Casts, backlash, no bites? Check the Nut holding the rod !! -